Knives and Tools: Ready Answers
How do I sharpen a recurve blade?
Quick answer
A recurve blade curves in, so a flat stone can't reach the hollow. Use a round sharpening rod, diamond to set the edge and ceramic to finish it, and keep the same angle, about 20 to 25 degrees, the whole way. In the field, turn a flat stone on its edge to reach the curve, then strop it smooth.
Quick answer: A recurve blade curves in, so a flat stone can't reach the hollow. Use a round sharpening rod, diamond to set the edge and ceramic to finish it, and keep the same angle, about 20 to 25 degrees, the whole way. In the field, turn a flat stone on its edge to reach the curve, then strop it smooth.
Why recurves are tricky
A recurve blade has an inward curve near the handle and a belly toward the tip. That shape cuts great, but a wide, flat stone only touches the high spots and skips the hollow. The fix is a sharpener that's narrow enough, or rounded enough, to reach into the curve.
Five ways that work
- 1. A large sharpening rod: the rounded surface reaches right into the recurve. Use the same number of strokes on each side, then switch. A ceramic rod takes an edge from sharp to razor sharp.
- 2. A rod with an angle guide: not sure of your angle? Cut a small scrap-wood wedge to about 20 degrees and tape it to the rod, then match your blade to the wedge.
- 3. A rod sharpener with preset angles: a base with holes set at 20 and 25 degrees holds diamond rods on one side and ceramic rods on the other. Hold the knife straight up and down and draw it down each rod. Most outdoor knives sit closer to 25 degrees, and smaller pocket knives closer to 20.
- 4. A pocket rod sharpener: the case turns into a handle, and it works the same way as the big rods while fitting in a pocket or pack.
- 5. The small rod on a field sharpener: many compact field sharpeners have a small diamond or ceramic rod built in. Skip the preset guides and use the rod for the recurve.
- Bonus field tip: if all you have is a standard flat stone, turn it at an angle and use its edge to reach the hollow, working from one corner to the other.
- For your pocket: the Tiny Knife Sharpener Kit has a credit-card-sized, double-sided diamond stone (500 grit on one side, 1000 grit on the other), a mini strop, a grip pad and honing compound. Use the edge of the card for the hollow, just like the bonus tip.
Steps
- 1. Find your angle. Match the angle of the existing bevel. A marker line on the edge shows you where you're removing steel.
- 2. Sharpen the straight and belly sections with normal strokes on the stone.
- 3. Work the hollow. Use the edge of the stone or a rod, in short strokes that follow the curve, keeping the same angle.
- 4. Raise a burr. Feel for a slight lip on the opposite side along the whole edge, then switch sides.
- 5. Move to the finer grit and lighten your pressure.
- 6. Strop with light, edge-trailing strokes until the burr is gone and the edge is smooth.
Tips
Go slow in the hollow; it's easy to grind a flat spot. Keep your fingers behind the edge, and never pull a stone toward your hand. A few light passes often is better than a big session once a year, and stropping between uses keeps a recurve working longer.
Watch it
HOW to SHARPEN a RE-CURVE KNIFE BLADE - LIKE a BOSS!!!! (Ultimate Survival Tips on YouTube)
Related questions
Can I sharpen a recurve on a flat stone?
Partly. A flat stone handles the belly, but you need the edge of the stone, a rod or a narrow sharpener to reach the hollow.
How do I know when the edge is sharp?
Feel for a small burr along the whole edge on the opposite side, then strop it off. A sharp edge cleanly slices paper.
Do I need to strop a recurve?
Stropping isn't required, but it removes the burr and polishes the edge so it stays sharp longer.
Keep it in your pocket
Tiny Survival Guide: Fire, water, shelter and first aid skills on a card that fits in your wallet.
More answers like this: Ready Answers: Knives and Tools
Be prepared, because you never know.
David Polczynski, founder of Ultimate Survival Tips
Related questions
Can I sharpen a recurve on a flat stone?
Partly. A flat stone handles the belly, but you need the edge of the stone, a rod or a narrow sharpener to reach the hollow.
How do I know when the edge is sharp?
Feel for a small burr along the whole edge on the opposite side, then strop it off. A sharp edge cleanly slices paper.
Do I need to strop a recurve?
Stropping isn't required, but it removes the burr and polishes the edge so it stays sharp longer.
Keep it in your pocket
Tiny Survival® Guide
Fire, water, shelter and first aid skills on a card that fits in your wallet.
Be prepared, because you never know.
David, Ultimate Survival Tips